Article

 

 

Listed here down the page you might get some incredibly good help and advice in relation to How to Install a Bathtub.

Setting up a tub isn't precisely brain surgery, however it does call for solid plumbing, woodworking, as well as sometimes, tiling skills. Replacing an old tub with a brand-new one is additionally a reasonably tough task. If the old bathtub is conveniently obtainable, the task can move rapidly; if you need to open a wall to remove the old tub and place the brand-new bath tub, the job is a lot harder. In either situation, the project is within a residence handyman's abilities, although you will certainly need a helper to move out the old bathtub and also embeded in the new one. See to it you have actually qualified yourself for the job and fit trying it. As opposed to employing a professional to take over a halfway-completed task, it is far better to take into consideration utilizing one before you start. Possibilities are you may need a professional plumber to make tube connections.
This article will certainly assist you install a brand-new tub in your bathroom if you have actually already acquired a new bathtub as well as don't require to change the setup of your previous supply of water pipelines.
Your tools and product checklist need to make up the following:

 

• New Bathtub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Degree


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Tape Measure


• Pipeline Caps


 

Removing Old Taps

If you require to replace old faucets with new ones as a part of your installation, then the first thing you need to do is detach the water supply. After doing so, switch on the faucets to drain any kind of water staying in the system. The procedure of eliminating the existing faucets can be quite troublesome as a result of the restricted accessibility that is frequently the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to undo the nut that links the supply pipelines to the taps. Have a towel ready for the staying water that will certainly come from the pipes. As soon as the supply pipes have been gotten rid of, use the exact same device to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary taps from turning throughout this procedure. Once the faucets have actually been removed, the holes in the bath/basin will certainly need to be cleansed of any old sealing substance.
Prior to carrying on to fit the new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.

 

 

Suitable New Taps

If the tails of the new faucets are plastic, after that you will need a plastic adapter to stop damage to the thread. One end of the port fits on the plastic tail of the faucet and the other end supplies a link to the current supply pipes.
If you need to fit a monobloc, then you will certainly need minimizing couplers, which connects the 10mm pipe of the monobloc to the typical 15mm supply pipe.
Next, position the tap in the installing opening in the bath/basin making certain that the washing machines are in place between the tap and the sink. Protect the tap in place with the producer supplied backnut. As soon as the tap is safely in place, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with regular faucet adapters. The previous kind should be attached to the faucet finishes initially, tightening only by hand. The supply pipes can later be connected to the various other end. Tighten up both ends with a spanner after both ends have been connected.

 

 

Installing the Bath tub

Making use of both wooden boards under its feet, place the bath tub in the needed setting. The wooden boards are practical in equally spreading out the weight of the bathtub over the location of the boards rather than focusing all the weight onto four small factors.
The following objective is to guarantee that the bathtub is leveled all round. This can be attained by examining the level as well as changing the feet on the tub until the spirit level reads degree.
To mount faucets, fit the bottom of the furthest flexible tap adapter to the ideal supply pipe by making a compression join; then do the exact same for the other faucet.
Activate the water as well as check all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bath tub as well as likewise check the overflow electrical outlet and the normal electrical outlet for leakages.
Lastly, fix the bathroom paneling as explained in the producer's user's manual. Tiling and securing around the bath tub must wait until the bathtub has been made use of at least when as this will settle it right into its final position.

 

 

Planning for the Setup

First of all, the sustaining framework supplied with the bathroom must be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is essential to see to it that if the tap comes with a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is also practical to fit a sustaining plate under the faucets unit to prevent pressure on the bathtub.
Fit the adaptable tap adapters to the bottom of the two faucets using 2 nuts and also olives (in some cases provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and after that pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Ensure you make use of every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its final placement.

 

 

Tiling Around the Bathtub

In the location where the bathroom meets the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is necessary as the fitting can move enough to split an inflexible seal, creating the water to penetrate the wall in between the bathroom and the tiling, leading to problems with moisture as well as feasible leakages to the ceiling listed below.
You can select from a selection of coloured sealants to blend in your components and also fittings. They are sold in tubes and also cartridges, and can securing spaces as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of soaked newspaper or soft rope. Keep in mind to constantly load the bath tub with water prior to sealing, to allow for the motion experienced when the bathtub remains in usage. The sealer can crack fairly very early if you do not think about this movement before securing.
Alternatively, ceramic coving or quadrant floor tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also easily offered on the market. It is recommended to fit the ceramic tiles utilizing water-resistant or water resistant adhesive and also grout.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

We were guided to that write-up about A Step-by-Step Guide to Installing a Bathtub through a good friend on our other website. Sharing is good. One never knows, you will be helping someone out. Thanks a lot for your time. Visit us again soon.

View Website